burner control units
Kromschroeder IFD 244 burner control unit
Ignites and monitors gas burners, for continuous operation, display for indicating program status and flame signal intensity, IP 54, EU certified, FM and CSA approved
Please sign in to access more documents
Once signed in, you may be able to access additional documents for your account.
Overview
Ignites and monitors gas burners, for continuous operation, display for indicating program status and flame signal intensity, IP 54, EU certified, FM and CSA approved.
Features & Benefits:
Features & Benefits:
- Series 200 Ionization control
- Restart in the event of flame failure
- Safety time on start-up: 10 s
- Safety time during operation: 1 s
- Mains voltage: 120 V AC, 50/60 Hz
Specifications
Standards & Certifications
- Approvals
- EN 298, Machinery Directive 2006/42/EC, Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC
Control, Safety & Timing Characteristics
- Start-up Safety Time
- 3, 5 or 10 seconds (model‑dependent)
Inputs, Outputs & Signal Interfaces
- Signal Input
- PLC-compatible signals (80-122.5 V at120 VAC or 160-253 V at230 VAC)
- Safety interlock input at terminal 3
- Outputs
- Ignition output max 2 A
- Signaling contacts max 2 A at 253 VAC
- Valve output max 1 A
Dimensions & Length Specifications
- Sensor Cable Length
- Ionisation cable up to 75 m; ignition cable up to 5 m (IFD 244)/1 m (IFD 244..I)
Safety, Protection & Reliability
- Safety Time During Operation
- <1 seconds or <2 seconds depending on version
- Fault Lock‑out
- Immediate lockout on failed start-up; coded fault messages via display (e.g., 02 = no flame)
Control, Logic & System Behavior
- Restart Function
- Automatic restart after flame failure during operation (single attempt)
Control, Software & User Interface Specifications
- Program Display
- 2‑digit 7‑segment display showing status, flame signal, and fault codes
Ignition, Flame & Supervision Specifications
- Integrated Ignition Specs
- Ignition voltage 22 kVpp, ignition current 25 mA, spark gap 2 to 5 mm (IFD 244..I)
- Ignition Type
- External ignition transformer (IFD 244) OR integrated ignition unit (IFD 244..I)
- Ignition Time
- Approximately 2, 3, or 6 seconds depending on model configuration
- Flame Monitoring
- Ionisation-based flame control with DC signal > 2 μA required for flame detection; measuring range 0-25 μA
Installation & Mounting Specifications
- Installation Type
- DIN‑rail snap‑mount or screw‑mount (M5), IP54 enclosure, any mounting position
Environmental Conditions
- Environmental Conditions
- -20 to +60 deg C (-4 to 140 deg F), no condensation
- Overvoltage category III; enclosure IP54
Electrical & Signal Specifications
- Electrical Rating
- 120 VAC or 230 VAC, -15/+10%, 50/60 Hz
- Power consumption approximately 9 VA (extra 25 VA during ignition for IFD 244..I)
Product Overview & Classification
- Device Type
- Automatic burner control unit for gas burners in continuous operation
Processing & Performance Metrics
- Capacity Range
- For directly ignited burners up to 350 kW
Standards & Certifications
- Approvals
- EN 298, Machinery Directive 2006/42/EC, Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC
Control, Safety & Timing Characteristics
- Start-up Safety Time
- 3, 5 or 10 seconds (model‑dependent)
Inputs, Outputs & Signal Interfaces
- Signal Input
- PLC-compatible signals (80-122.5 V at120 VAC or 160-253 V at230 VAC)
- Safety interlock input at terminal 3
- Outputs
- Ignition output max 2 A
- Signaling contacts max 2 A at 253 VAC
- Valve output max 1 A
Dimensions & Length Specifications
- Sensor Cable Length
- Ionisation cable up to 75 m; ignition cable up to 5 m (IFD 244)/1 m (IFD 244..I)
Safety, Protection & Reliability
- Safety Time During Operation
- <1 seconds or <2 seconds depending on version
- Fault Lock‑out
- Immediate lockout on failed start-up; coded fault messages via display (e.g., 02 = no flame)
Control, Logic & System Behavior
- Restart Function
- Automatic restart after flame failure during operation (single attempt)
Control, Software & User Interface Specifications
- Program Display
- 2‑digit 7‑segment display showing status, flame signal, and fault codes
Ignition, Flame & Supervision Specifications
- Integrated Ignition Specs
- Ignition voltage 22 kVpp, ignition current 25 mA, spark gap 2 to 5 mm (IFD 244..I)
- Ignition Type
- External ignition transformer (IFD 244) OR integrated ignition unit (IFD 244..I)
- Ignition Time
- Approximately 2, 3, or 6 seconds depending on model configuration
- Flame Monitoring
- Ionisation-based flame control with DC signal > 2 μA required for flame detection; measuring range 0-25 μA
Installation & Mounting Specifications
- Installation Type
- DIN‑rail snap‑mount or screw‑mount (M5), IP54 enclosure, any mounting position
Environmental Conditions
- Environmental Conditions
- -20 to +60 deg C (-4 to 140 deg F), no condensation
- Overvoltage category III; enclosure IP54
Electrical & Signal Specifications
- Electrical Rating
- 120 VAC or 230 VAC, -15/+10%, 50/60 Hz
- Power consumption approximately 9 VA (extra 25 VA during ignition for IFD 244..I)
Product Overview & Classification
- Device Type
- Automatic burner control unit for gas burners in continuous operation
Processing & Performance Metrics
- Capacity Range
- For directly ignited burners up to 350 kW
- Approvals : EN 298, Machinery Directive 2006/42/EC, Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC
- Start-up Safety Time : 3, 5 or 10 seconds (model‑dependent)
- Signal Input : PLC-compatible signals (80-122.5 V at120 VAC or 160-253 V at230 VAC)|Safety interlock input at terminal 3
- Sensor Cable Length : Ionisation cable up to 75 m; ignition cable up to 5 m (IFD 244)/1 m (IFD 244..I)
- Safety Time During Operation : <1 seconds or <2 seconds depending on version
- Restart Function : Automatic restart after flame failure during operation (single attempt)
- Program Display : 2‑digit 7‑segment display showing status, flame signal, and fault codes
- Outputs : Ignition output max 2 A|Signaling contacts max 2 A at 253 VAC|Valve output max 1 A
- Integrated Ignition Specs : Ignition voltage 22 kVpp, ignition current 25 mA, spark gap 2 to 5 mm (IFD 244..I)
- Installation Type : DIN‑rail snap‑mount or screw‑mount (M5), IP54 enclosure, any mounting position
- Ignition Type : External ignition transformer (IFD 244) OR integrated ignition unit (IFD 244..I)
- Ignition Time : Approximately 2, 3, or 6 seconds depending on model configuration
- Flame Monitoring : Ionisation-based flame control with DC signal > 2 μA required for flame detection; measuring range 0-25 μA
- Fault Lock‑out : Immediate lockout on failed start-up; coded fault messages via display (e.g., 02 = no flame)
- Environmental Conditions : -20 to +60 deg C (-4 to 140 deg F), no condensation|Overvoltage category III; enclosure IP54
- Electrical Rating : 120 VAC or 230 VAC, -15/+10%, 50/60 Hz|Power consumption approximately 9 VA (extra 25 VA during ignition for IFD 244..I)
- Device Type : Automatic burner control unit for gas burners in continuous operation
- Capacity Range : For directly ignited burners up to 350 kW
Name
Description
File Size
Date
Size
Please sign in to view part numbers available for purchase based on your account Sign In
Part Number
Description
Leaf Category
Thumbnail
Add to list
