burner control units
Kromschroeder IFD 258 burner control unit
Ignites and monitors gas burners, for continuous operation with ionization control, adjustable cut-off point, display for indicating program status and flame signal intensity, IP 54, EU certified, FM and CSA approved
Please sign in to access more documents
Once signed in, you may be able to access additional documents for your account.
Overview
Ignites and monitors gas burners, for continuous operation with ionization control, adjustable cut-off point, display for indicating program status and flame signal intensity, IP 54, EU certified, FM and CSA approved.
Features & Benefits:
Features & Benefits:
- Series 200
- Ionization or UV control
- Immediate fault lock-out or restart in the event of flame failure, switchable
- Safety time on start-up: 10 s
- Safety time during operation: 1 s
- Mains voltage: 120 V AC, 50/60 Hz
Specifications
Inputs, Outputs & Signal Interfaces
- Outputs
- Ignition: max 2 A; Valve output: max 1 A; Signaling contacts: max 2 A at 253 VAC
Safety, Protection & Reliability
- Safety Time During Operation
- Default 1 seconds, optional 2 seconds, must not exceed 3 seconds as per EN 746-2
Control, Logic & Functional Behavior
- Start-up Sequence Controls
- Waiting time tW, flame simulation check, safety time tSA, ignition time tZ; lockout if flame not detected within tSA
Control, Logic & System Behavior
- Restart/Lockout Behavior
- Switch‑selectable: immediate fault lockout or one‑off restart on flame failure
Environmental Conditions
- Environmental Conditions
- -20 to +60 deg C (-4 to +140 deg F)
- Overvoltage category III, no condensation
Control, Safety & Timing Characteristics
- Start-up Safety Time
- Selectable: 3, 5, or 10 seconds (model dependent)
Ignition, Flame & Supervision Specifications
- Permitted UV Sensors
- Elster Kromschröder UVS 1, 5, 6, 10 (-40 to +80 deg C)
- Flame Monitoring
- Ionization sensor or UV sensor (UVS); UV mode only for intermittent operation; signal range 0-25 µA; detection ≥ 2 µA
- Ignition Type
- External ignition transformer (IFD 258) or integrated ignition (IFD 258..I) with 22 kVpp ignition voltage and 25 mA current
- Ignition Time
- Approximately 2, 3, or 6 seconds depending on model configuration
Dimensions & Length Specifications
- Sensor Cable Length
- Ionization: max 75 m; UV sensor: max 100 m; ignition cable: up to 5 m (IFD 258)/1 m (IFD 258..I)
Operating Limits, Durability & Lifecycle
- Operating Cycles
- Control unit: 250,000 cycles; Reset and mains buttons: 1000 cycles each
Control, Software & User Interface Specifications
- Program Display
- 2‑digit 7‑segment display for program status, flame signal, and fault codes (00, 01, 02, 04, 09, 10, 52, 53)
Processing & Performance Metrics
- Capacity Range
- Unlimited capacity burners (atmospheric or forced-draught)
Electrical Specifications
- Mains Voltage
- 100 V, 120 V, 200 V, 230 VAC (-15%/+10%), 50/60 Hz
Material Specifications
- Body Material
- Impact‑resistant plastic housing
Product Overview & Classification
- Device Type
- Automatic burner control unit for directly ignited industrial gas burners in continuous operation
Standards & Certifications
- Approvals
- EN 298, Machinery Directive 2006/42/EC, Gas Appliances Directive, Low Voltage Directive, EMC Directive; AGA, FM, CSA, GOST‑R approvals
Inputs, Outputs & Signal Interfaces
- Outputs
- Ignition: max 2 A; Valve output: max 1 A; Signaling contacts: max 2 A at 253 VAC
Safety, Protection & Reliability
- Safety Time During Operation
- Default 1 seconds, optional 2 seconds, must not exceed 3 seconds as per EN 746-2
Control, Logic & Functional Behavior
- Start-up Sequence Controls
- Waiting time tW, flame simulation check, safety time tSA, ignition time tZ; lockout if flame not detected within tSA
Control, Logic & System Behavior
- Restart/Lockout Behavior
- Switch‑selectable: immediate fault lockout or one‑off restart on flame failure
Environmental Conditions
- Environmental Conditions
- -20 to +60 deg C (-4 to +140 deg F)
- Overvoltage category III, no condensation
Control, Safety & Timing Characteristics
- Start-up Safety Time
- Selectable: 3, 5, or 10 seconds (model dependent)
Ignition, Flame & Supervision Specifications
- Permitted UV Sensors
- Elster Kromschröder UVS 1, 5, 6, 10 (-40 to +80 deg C)
- Flame Monitoring
- Ionization sensor or UV sensor (UVS); UV mode only for intermittent operation; signal range 0-25 µA; detection ≥ 2 µA
- Ignition Type
- External ignition transformer (IFD 258) or integrated ignition (IFD 258..I) with 22 kVpp ignition voltage and 25 mA current
- Ignition Time
- Approximately 2, 3, or 6 seconds depending on model configuration
Dimensions & Length Specifications
- Sensor Cable Length
- Ionization: max 75 m; UV sensor: max 100 m; ignition cable: up to 5 m (IFD 258)/1 m (IFD 258..I)
Operating Limits, Durability & Lifecycle
- Operating Cycles
- Control unit: 250,000 cycles; Reset and mains buttons: 1000 cycles each
Control, Software & User Interface Specifications
- Program Display
- 2‑digit 7‑segment display for program status, flame signal, and fault codes (00, 01, 02, 04, 09, 10, 52, 53)
Processing & Performance Metrics
- Capacity Range
- Unlimited capacity burners (atmospheric or forced-draught)
Electrical Specifications
- Mains Voltage
- 100 V, 120 V, 200 V, 230 VAC (-15%/+10%), 50/60 Hz
Material Specifications
- Body Material
- Impact‑resistant plastic housing
Product Overview & Classification
- Device Type
- Automatic burner control unit for directly ignited industrial gas burners in continuous operation
Standards & Certifications
- Approvals
- EN 298, Machinery Directive 2006/42/EC, Gas Appliances Directive, Low Voltage Directive, EMC Directive; AGA, FM, CSA, GOST‑R approvals
- Outputs : Ignition: max 2 A; Valve output: max 1 A; Signaling contacts: max 2 A at 253 VAC
- Safety Time During Operation : Default 1 seconds, optional 2 seconds, must not exceed 3 seconds as per EN 746-2
- Start-up Sequence Controls : Waiting time tW, flame simulation check, safety time tSA, ignition time tZ; lockout if flame not detected within tSA
- Restart/Lockout Behavior : Switch‑selectable: immediate fault lockout or one‑off restart on flame failure
- Environmental Conditions : -20 to +60 deg C (-4 to +140 deg F)|Overvoltage category III, no condensation
- Start-up Safety Time : Selectable: 3, 5, or 10 seconds (model dependent)
- Permitted UV Sensors : Elster Kromschröder UVS 1, 5, 6, 10 (-40 to +80 deg C)
- Sensor Cable Length : Ionization: max 75 m; UV sensor: max 100 m; ignition cable: up to 5 m (IFD 258)/1 m (IFD 258..I)
- Operating Cycles : Control unit: 250,000 cycles; Reset and mains buttons: 1000 cycles each
- Flame Monitoring : Ionization sensor or UV sensor (UVS); UV mode only for intermittent operation; signal range 0-25 µA; detection ≥ 2 µA
- Program Display : 2‑digit 7‑segment display for program status, flame signal, and fault codes (00, 01, 02, 04, 09, 10, 52, 53)
- Capacity Range : Unlimited capacity burners (atmospheric or forced-draught)
- Mains Voltage : 100 V, 120 V, 200 V, 230 VAC (-15%/+10%), 50/60 Hz
- Ignition Type : External ignition transformer (IFD 258) or integrated ignition (IFD 258..I) with 22 kVpp ignition voltage and 25 mA current
- Ignition Time : Approximately 2, 3, or 6 seconds depending on model configuration
- Body Material : Impact‑resistant plastic housing
- Device Type : Automatic burner control unit for directly ignited industrial gas burners in continuous operation
- Approvals : EN 298, Machinery Directive 2006/42/EC, Gas Appliances Directive, Low Voltage Directive, EMC Directive; AGA, FM, CSA, GOST‑R approvals
Name
Description
File Size
Date
Size
Please sign in to view part numbers available for purchase based on your account Sign In
Part Number
Description
Leaf Category
Thumbnail
Add to list
